Your plumbing system, like you and your family, is an important part of your home. Just like you, it needs to be be taken care of. You need to research all kinds of techniques and equipment and find what works for your plumbing job. These tips below can help you with that.
You always want to solder correctly, the biggest mistake most people make when soldering is failing to get the interior of the fitting and the exterior of the pipe clean and shiny. Polish these surfaces with a fine emery clot until bright. When soldering, never heat the pipe, but instead heat the fitting. Doing so allows the solder to be drawn into the fitting by capillary action.
To avoid wasting water and having a potentially high water bill, check your home for leaky faucets periodically. Fix any leaks that you find right away. You may be able to do the repair yourself, but if not, you may have to seek the services of a plumber to make the repairs.
You can check your toilet for leaks by adding a few drops of food coloring, Kool Aid or some coffee grounds to the water in the toilet’s tank (not the water in the bowl). Check the water in the bowl after a half hour or so. If any of the coloring agent is visible in the water in the bowl, the tank is leaking, and you will have to have it repaired.
Never put your hands in your garbage disposal to fix a problem. Even when in the off position, garbage disposals are dangerous. You can look online to find the diagram for the disposal that you have.
Have all the plumbing repairs done in one visit. While you may be tempted to call the plumber whenever you have a slight problem, scheduling it all at once gives you the opportunity to save money to pay for the repairs. Because most plumbers charge labor by the hour on top of a flat call rate, you can significantly reduce your bill by reducing the trips they make to your home.
Make sure everyone in your home knows where the main water shut off valve is and that they know how to work it. That way, if there is a water problem, anyone in your household can turn off the water, thereby reducing the chances that your home will incur major water damage.
Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.
Everyone in your home should know where the main water shut off valve is. By knowing where to find this valve, you’ll be able to shut off the water in the event a pipe bursts, a bathtub or toilet overflows or any other emergency that requires you to turn off the water.
To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.
During the winter months, your water heater works the hardest. To keep it in optimum condition, flush it out before winter arrives. Flushing the system helps remove the sediment buildup, which causes internal corrosion of your water heater, shortens its lifespan, and reduces heating efficiency. Connect a hose to the faucet near the bottom of the tank and drain several gallons by directing the water into a nearby drain.
Make sure that the temperature of your home’s water heater is not above 120F. On older water heaters, be sure it is not above medium settings. When temperatures get higher than 120, scalding can occur. Also, having the settings above 120F, tends to use more energy than lower temperatures do.
Make sure you shut off your main system before leaving your house for a few weeks. The water will stay in the pipes, but this should prevent any further damages in case a leak starts while you are away. Check that your shut-off valve is working properly before you leave.
Check to make sure that the walls behind the tiles in your bathroom are not soft. Push into the tiles to confirm that the foundation is firm and robust. If the area is delicate and brittle, there is a good chance that water has created damage behind the tiles over time.
Plumbing choices can come in many ways. One decision you need to make as a homeowner is to purchase a tank-less water heater. One thing to remember if you are considering a tank-less heater. You will pay two to three times more than if you purchase a tank heater.
When it comes to plumbing, there is never an unsolvable problem. If you feel yourself becoming frustrated with the project, you should try to take a break from what you are working on. The greatest mistakes start to happen when you become angry and inpatient, so take a break and walk outside.
To prepare for the cold weather, properly drain all outside faucet bibs and turn off the water supply to those faucets. A piece of foam taped to the outside bib can provide excellent insulation to prevent any remaining water from freezing or splurge for a specialty cover that comes complete with velcro closures.
Doing your own plumbing ensures that if anything happens to it, you can fix it. Similar to taking care of your family, it is really important that you take care of your plumbing system. So, do yourself a favor and do your research and apply the above tips to your plumbing jobs.Family Bunker Plans,Click here! Family Self Defense (view mobile),Click here!